How to Make Wrapped Leather Bracelets

Thanks for Rings and Things for this one!

Triple-wrap leather bracelet with blue tigereye beads

Let me begin by stating the obvious – this style of wrapped leather bracelet is EVERYWHERE this season.  Everywhere! Even my athletic clothing catalogs – which only have maybe three pieces of jewelry – are featuring this style. Why? Because it is casual yet chic and infinitely customizable! The catalog (which shall remain nameless) priced each bracelet at $120. Needless to say, you can make your own for far, far less using supplies from Rings & Things!

Five different leather wrapped gemstone bracelets designs: green opal, mookaite, African turquoise, hematite and rhodonite

The supply list is pretty short:

• 6mm round beads We used gemstones, but glass, crystals or pearls would also be lovely.  The number you need depends on  how many times you want to wrap the bracelet around your wrist. Larger beads work too – but they will start getting heavy on multiple-wrap styles.
• Leather cord Our examples use Greek leather. Both the 1.5mm and 2mm worked great.
• Thread Needs to be sturdy and able to pass (doubled) through your beads twice.  Pick a color that matches your leather or that provides a pretty contrast. We used size D SuperLon (specifically, the earth assortment).
• Button or bead for the clasp. Rings & Things has some pretty ones from TierraCast.
• Required tools: needle, scissors, work surface with clips or clothespins.
• Optional tools: needle threader, thread conditioner, glue (GS Hypo Cement, Bead Fix or other fabric-friendly adhesive for extra security on your knots).

Wrapped bracelet made with green opal gemstone beads and natural Greek leather.

The technique:

1. Choose your bracelet length and cut your leather. The formula is double your finished bracelet length plus extra for making the knots. For single-wrap bracelet, measure your wrist and then triple that number to get the length of leather needed (7″ wrist = 21″ of leather). For a triple-wrap, multiply your wrist by seven (7″ wrist = 49″ leather). It is better to leave your leather too long than to end up with not enough.
2. Cut a long piece of thread (10-12 feet) and thread your needle. Knot the end of the threads.
3. 
   

   Knot the leather and thread together, leaving a loop on the end.
   Holding the thread by the knot, let the needle fall to the ground so it is centered on the thread. Fold your piece of leather in half, leaving a loop large enough for your button to fit through. Holding the knot-end of the thread with the leather, tie an overhand knot so that your thread and leather are now connected.
   
   
   

   Make sure your button will fit through the loop before you tighten the knot.
4. 
   

   Attach your piece to a work surface.
   Using binder clips or clothespins, attach your loop to the top of a piece of cardboard. Use a second clip to attach the leather ends to the bottom of your board (leave the thread loose).
5. Starting with your thread in the middle of the two strands of leather, wrap the thread OVER the right strand to the outside, then UNDER the right, OVER the left to the outside, then UNDER the left and OVER the right. It is a simple figure-8 stitch.
   
   

   Over, under, over, under - once you get a rhythm going, the bracelet is super easy to make!
   Do this 5-6 times, pulling the thread tight around the leather to form a binding.  (The pattern could go either way, but since I’m right-handed I’m going to describe it this way.  Reverse it if needed!) Here is a close-up of the lashing:
   
   
   

   A few stitches without beads secures the thread nicely on the leather.
6. Now you are ready to start adding beads. After your thread has passed UNDER the left leather, add a bead. Hold the bead between the two strands of leather, and stitch the thread OVER the right, back UNDER the right,  THROUGH the bead hole again and OVER the left.  Bring the thread UNDER the left and add another bead in the middle. Repeat many many times! Keep the beads pulled in snugly against the leather. Pay attention so that your stitches all face the same way. If your thread seems to snag a lot, use a bit of thread conditioner or beeswax on it.
   
   

   Adding the first bead to a wrapped bracelet - but really I'm posting this picture to show off Jaci's manicure!
   
   

   A work in progress. See how the beads line up inside the leather?
7. To finish the bracelet, form several stitches without beads, just like you did in step 5.  Now you are ready to attach your button or bead.  Ideally, you’ll have enough leather left to tie on a button with a nice knot on the back and trim the ends.
   
   

   Long tails makes it easy to tie on a button closure.
   
   

   If your button has a small loop, you might need to miter (angle) the leather end and pull it through with pliers.
   
   

   Buttons, disk beads and crimp ends can all be used to finish the bracelet ends.
   If somehow you come up short, all is not lost. You can tie a disk bead onto just one strand of the leather (use glue to enforce your knot), like on the 2nd bracelet from the left. Or if your ends are really short, use a hook-end crimp, as shown on the pink bracelet on the right.
8. If desired, add a touch of glue to the knots to ensure the thread is gripped securely by the leather. Trim ends as needed.

Other design options:

• String your button or bead clasp first, then tie a series of knots on the end to make the bracelet length adjustable.
• Use jump rings to attach a couple of charms, like on Mollie’s Belle Star bracelet.
• Leave the leather tails long and add beads or decorative knots.
• Substitute a different type of cord for the leather, as in Tracy’s rattail and dragon blood jasper design:

Have fun creating your own wrapped bracelets! You’ll find it is quite addictive once you start. Please feel free to post questions – I will do my best to answer! ~ Cindy